connected through serial console port, ttyS0, 115200 8N1, Con401 Port
+FLASH configuration checksum error or invalid key
Network NOT initialized!
Press FSG Emergency Button during power up to initialize network
RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 1.94 - built 11:47:48, Jun 10 2005
Platform: Freecom Storage Gateway (FSG) (XScale) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
RAM: 0x00000000-0x04000000, 0x0001db58-0x03fd1000 available
FLASH: 0x50000000 - 0x50400000, 32 blocks of 0x00020000 bytes each.
RedBoot> fis load kern1
RedBoot> exec -c "console=ttyS0,115200 root=/dev/sda1 init=/etc/preinit "
Using base address 0x00700000 and length 0x00180000
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.37.6 (cave@cave.site) (gcc version 4.5.4 20110808 (prerelease2
[ 0.000000] CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Freecom FSG-3
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 64MB = 64MB total
[ 0.000000] Memory: 61628k/61628k available, 3908k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0026000 ( 120 kB)
[ 0.000000] .text : 0xc0026000 - 0xc030c000 (2968 kB)
[ 0.000000] .data : 0xc030c000 - 0xc03288e0 ( 115 kB)
[ 0.000000] NR_IRQS:64
[ 0.000305] Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
[ 0.240088] pid_max: default: 32768 minimum: 301
[ 0.240655] Mount-cache hash table entries: 512
[ 0.241540] CPU: Testing write buffer coherency: ok
[ 0.246593] NET: Registered protocol family 16
[ 0.251910] IXP4xx: Using 16MiB expansion bus window size
[ 0.255906] FSG: Using MAC address 00:01:db:00:a7:78 for port 0
[ 0.255960] FSG: Using MAC address 00:01:db:00:a7:79 for port 1
[ 0.256633] PCI: IXP4xx is host
[ 0.256671] PCI: IXP4xx Using direct access for memory space
[ 0.259319] PCI: bus0: Fast back to back transfers disabled
[ 0.259402] pci 0000:00:0c.0: dmabounce: registered device
[ 0.260331] pci 0000:00:0e.0: dmabounce: registered device
[ 0.261139] pci 0000:00:0e.1: dmabounce: registered device
[ 0.261968] pci 0000:00:0e.2: dmabounce: registered device
[ 0.262767] fsg_map_irq: Mapped slot 1 pin 1 to IRQ 22
[ 0.262830] fsg_map_irq: Mapped slot 3 pin 1 to IRQ 23
[ 0.262881] fsg_map_irq: Mapped slot 3 pin 2 to IRQ 23
[ 0.262932] fsg_map_irq: Mapped slot 3 pin 3 to IRQ 23
[ 0.263036] pci 0000:00:0e.0: BAR 0: assigned [mem 0x48000000-0x48000fff]
[ 0.263107] pci 0000:00:0e.0: BAR 0: set to [mem 0x48000000-0x48000fff] (PCI address [0x480)
[ 0.263175] pci 0000:00:0e.1: BAR 0: assigned [mem 0x48001000-0x48001fff]
[ 0.263237] pci 0000:00:0e.1: BAR 0: set to [mem 0x48001000-0x48001fff] (PCI address [0x480)
[ 0.263302] pci 0000:00:0c.0: BAR 5: assigned [io 0x1000-0x10ff]
[ 0.263360] pci 0000:00:0c.0: BAR 5: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff)
[ 0.263422] pci 0000:00:0e.2: BAR 0: assigned [mem 0x48002000-0x480020ff]
[ 0.263485] pci 0000:00:0e.2: BAR 0: set to [mem 0x48002000-0x480020ff] (PCI address [0x480)
[ 0.263549] pci 0000:00:0c.0: BAR 4: assigned [io 0x1400-0x141f]
[ 0.263608] pci 0000:00:0c.0: BAR 4: set to [io 0x1400-0x141f] (PCI address [0x1400-0x141f)
[ 0.263668] pci 0000:00:0c.0: BAR 0: assigned [io 0x1420-0x142f]
[ 0.263726] pci 0000:00:0c.0: BAR 0: set to [io 0x1420-0x142f] (PCI address [0x1420-0x142f)
[ 0.263786] pci 0000:00:0c.0: BAR 1: assigned [io 0x1430-0x143f]
[ 0.263845] pci 0000:00:0c.0: BAR 1: set to [io 0x1430-0x143f] (PCI address [0x1430-0x143f)
[ 0.263906] pci 0000:00:0c.0: BAR 2: assigned [io 0x1440-0x144f]
[ 0.263964] pci 0000:00:0c.0: BAR 2: set to [io 0x1440-0x144f] (PCI address [0x1440-0x144f)
[ 0.264026] pci 0000:00:0c.0: BAR 3: assigned [io 0x1450-0x145f]
[ 0.264085] pci 0000:00:0c.0: BAR 3: set to [io 0x1450-0x145f] (PCI address [0x1450-0x145f)
[ 0.288037] bio: create slab <bio-0> at 0
[ 0.292517] SCSI subsystem initialized
[ 0.297214] usbcore: registered new interface driver usbfs
[ 0.297948] usbcore: registered new interface driver hub
[ 0.298689] usbcore: registered new device driver usb
[ 0.300713] i2c-gpio i2c-gpio.0: using pins 12 (SDA) and 13 (SCL)
[ 0.304250] Switching to clocksource OSTS
[ 0.312137] NET: Registered protocol family 2
[ 0.312517] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.313252] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.313429] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.313550] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.313589] TCP reno registered
[ 0.313629] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.313710] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.314305] NET: Registered protocol family 1
[ 0.317006] IXP4xx Queue Manager initialized.
[ 0.322559] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.322621] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-200.
[ 0.324047] msgmni has been set to 120
[ 0.324177] io scheduler noop registered
[ 0.324209] io scheduler deadline registered (default)
[ 1.075228] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.085638] serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
[ 1.590323] console [ttyS0] enabled
[ 1.597896] serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
[ 1.609164] PCI: enabling device 0000:00:0c.0 (0000 -> 0001)
[ 1.615394] sata_via 0000:00:0c.0: routed to hard irq line 6
[ 1.629567] scsi0 : sata_via
[ 1.634586] scsi1 : sata_via
[ 1.639259] scsi2 : sata_via
[ 1.643749] ata1: SATA max UDMA/133 port i16@0x1420 bmdma 0x1400 irq 22
[ 1.650491] ata2: SATA max UDMA/133 port i16@0x1430 bmdma 0x1408 irq 22
[ 1.657155] ata3: PATA max UDMA/133 port i16@0x1440 bmdma 0x1410 irq 22
[ 1.668829] IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x006
[ 1.679379] Intel/Sharp Extended Query Table at 0x0031
[ 1.684609] Intel/Sharp Extended Query Table at 0x0031
[ 1.689812] Using buffer write method
[ 1.693486] cfi_cmdset_0001: Erase suspend on write enabled
[ 1.699398] Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x3e0000
[ 1.829678] 6 RedBoot partitions found on MTD device IXP4XX-Flash.0
[ 1.836075] IXP4xx flash: using dynamic partition definition
[ 1.841753] Creating 6 MTD partitions on "IXP4XX-Flash.0":
[ 1.847321] 0x000000000000-0x000000040000 : "RedBoot"
[ 1.857869] 0x000000080000-0x000000200000 : "kern1"
[ 1.867975] 0x000000200000-0x000000380000 : "kern2"
[ 1.877852] 0x0000003a0000-0x0000003c0000 : "microcode"
[ 1.888146] 0x0000003c0000-0x0000003e0000 : "RedBoot config"
[ 1.898952] 0x0000003e0000-0x000000400000 : "FIS directory"
[ 1.922139] IXP4xx MII Bus: probed
[ 1.927778] eth0: MII PHY 5 on NPE-B
[ 1.933466] eth1: MII PHY 4 on NPE-C
[ 1.937787] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.945163] PCI: enabling device 0000:00:0e.2 (0140 -> 0142)
[ 1.951069] ehci_hcd 0000:00:0e.2: EHCI Host Controller
[ 1.956659] ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
[ 1.994438] ehci_hcd 0000:00:0e.2: irq 23, io mem 0x48002000
[ 2.014363] ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00
[ 2.023069] hub 1-0:1.0: USB hub found
[ 2.026986] hub 1-0:1.0: 5 ports detected
[ 2.032328] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.038756] PCI: enabling device 0000:00:0e.0 (0140 -> 0142)
[ 2.044734] ohci_hcd 0000:00:0e.0: OHCI Host Controller
[ 2.050101] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
[ 2.057787] ohci_hcd 0000:00:0e.0: irq 23, io mem 0x48000000
[ 2.147562] hub 2-0:1.0: USB hub found
[ 2.151401] hub 2-0:1.0: 3 ports detected
[ 2.156208] PCI: enabling device 0000:00:0e.1 (0140 -> 0142)
[ 2.162119] ohci_hcd 0000:00:0e.1: OHCI Host Controller
[ 2.167592] ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
[ 2.175213] ohci_hcd 0000:00:0e.1: irq 23, io mem 0x48001000
[ 2.192162] ata1: SATA link down (SStatus 0 SControl 310)
[ 2.267517] hub 3-0:1.0: USB hub found
[ 2.271349] hub 3-0:1.0: 2 ports detected
[ 2.276770] Initializing USB Mass Storage driver...
[ 2.282737] usbcore: registered new interface driver usb-storage
[ 2.288863] USB Mass Storage support registered.
[ 2.296659] rtc-isl1208 0-006f: chip found, driver version 0.3
[ 2.304030] rtc-isl1208 0-006f: rtc core: registered rtc-isl1208 as rtc0
[ 2.311435] rtc-isl1208 0-006f: rtc power failure detected, please set clock.
[ 2.320391] i2c /dev entries driver
[ 2.335274] hwmon-vid: Unknown VRM version of your CPU
[ 2.356886] IXP4xx Watchdog Timer: heartbeat 60 sec
[ 2.368756] TCP westwood registered
[ 2.372272] NET: Registered protocol family 17
[ 2.377088] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 2.383904] All bugs added by David S. Miller <davem@redhat.com>
[ 2.390077] XScale DSP coprocessor detected.
[ 2.401011] rtc-isl1208 0-006f: hctosys: invalid date/time
[ 2.555531] ata2: SATA link down (SStatus 0 SControl 310)
[ 2.735171] ata3.00: ATA-7: Hitachi HDT725050VLAT80, V56OA4NA, max UDMA/133
[ 2.742174] ata3.00: 976773168 sectors, multi 0: LBA48
[ 2.747506] ata3.00: limited to UDMA/33 due to 40-wire cable
[ 2.785030] ata3.00: configured for UDMA/33
[ 2.790169] scsi 2:0:0:0: Direct-Access ATA Hitachi HDT72505 V56O PQ: 0 ANSI: 5
[ 2.801579] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 2.810531] sd 2:0:0:0: [sda] Write Protect is off
[ 2.815910] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPA
[ 2.843099] sda: sda1 sda2 sda3 sda4
[ 2.852510] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.864578] REISERFS (device sda1): found reiserfs format "3.6" with standard journal
[ 2.872614] REISERFS (device sda1): using ordered data mode
[ 2.888771] REISERFS (device sda1): journal params: device sda1, size 8192, journal first b0
[ 2.909213] REISERFS (device sda1): checking transaction log (sda1)
[ 2.960615] REISERFS (device sda1): replayed 8 transactions in 0 seconds
[ 2.968299] REISERFS (device sda1): Using r5 hash to sort names
[ 2.974596] VFS: Mounted root (reiserfs filesystem) on device 8:1.
[ 2.980941] Freeing init memory: 120K
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
Please press Enter to activate this console. [ 10.936848] PPP generic driver version 2.4.2
[ 11.213930] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.542142] NET: Registered protocol family 24
[ 11.841132] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 12.559435] ath_hal: module license 'Proprietary' taints kernel.
[ 12.565569] Disabling lock debugging due to kernel taint
[ 12.616639] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF)
[ 12.790405] ath_pci: trunk
[ 12.793159] wlan: trunk
[ 12.795712] wlan: mac acl policy registered
[ 12.799921] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
[ 12.807711] ath_rate_minstrel: look around rate set to 10%
[ 12.813215] ath_rate_minstrel: EWMA rolloff level set to 75%
[ 12.818912] ath_rate_minstrel: max segment size in the mrr set to 6000 us
[ 12.887759] uhci_hcd: USB Universal Host Controller Interface driver
[ 14.646119] NPE-B: firmware's license can be found in /usr/share/doc/LICENSE.IPL
[ 14.653556] NPE-B: firmware functionality 0x2, revision 0x2:1
[ 15.045271] device eth0 entered promiscuous mode
[ 15.150342] br-lan: port 1(eth0) entering forwarding state
[ 15.155968] br-lan: port 1(eth0) entering forwarding state
[ 15.944685] eth0: link up, speed 100 Mb/s, full duplex
BusyBox v1.19.3 (2012-01-04 22:57:01 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r29660) ----------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#
Keine Kommentare:
Kommentar veröffentlichen